how to set up above ground pool on unlevel ground

HOW TO SET UP ABOVE GROUND POOL ON UNLEVEL GROUND HOW TO
HOW TO SET UP ABOVE GROUND POOL ON UNLEVEL GROUND INSTALL

It’s also worth mentioning that you should avoid adding soil to the pool when leveling. Where’s the lowest point of the pool? It’s crucial to figure this out and, of course, ensure that the rest of the pool area at the same level (any mistake at this point can ruin the entire process and may even require a need for remodeling services). Finally, hammer the plank’s 4-inch nail into the center of the square stake so it can rotate around the pool area.Ĩ. Next up, take out the metal stake (at the center of the pool) and drive a 2-inch square stake into the ground. Now, using a hammer, drive a 4-inch nail halfway into a 1-inch side of the plank. This is where you’ll get a 1-inch by 6-inch plank of wood (one that’s six inches longer than the radius of the pool) and duct tape a 4-foot level to the plank centered on one end of the 1- inch sides. Once you’re done cleaning the area, you can start arranging your wooden plank level. Marked the area? Well, now it’s time to get rid of everything from the grass to the sod and roots (basically anything that shouldn’t be in the workspace).ħ. The goal here is to locate the area on the grass that should be leveled. Once done, pull the string out to the grass (and mark it at the 6-inch mark). Now take a can of spray paint and tie it to the loose end of the string. If such is the case, get a piece of string (preferably one that is six inches longer than the radius of your pool) and tie it to the metal stake. At this point, chances are the sand is firm (or better still, confirm that it is). With this in mind, you would want to do your best to comply accordingly.Ħ. Speaking of which, you should be aware that some districts require that swimming pools maintain a center distance from existing buildings or property lines (and that includes your home). Using a metal stake, drive a hole into the middle area of the pool, while making sure that it goes in line with building codes for correct placement and proper compliance with local ordinances. If it does, you might end up needing a repair or remodeling.ĥ. At this point, You’ll do well to walk over the area and, of course, confirm that it leaves no impression on the ground. It’s incredibly important to ensure that the entire area or circle is done correctly. Be sure to keep at it until you find that the sand is hard and compact. Done with the leveling? Now it’s time to wet the area, get your tamper, and use the same to tamp down the sand. Be sure to pour as much sand as needed and, of course, keep rotating the boards until it indicates that the sand is level properly.Ĥ. Done? Now you should get sand and pour it over the area with a primary focus on the low area of the pool. Afterward, drive a metal rod through the tunnel to secure the 2-by-4 boards to the ground. Right now, you’ll want to drill a 3/8-inch hole right through the middle of the 2-by-4s. Doing this will give you a better idea of just how unlevel the ground is.ģ. At this point, you can easily measure the distance between the bottom of the 2-by-4 to the ground.

Once done, gently lift and lower one end of the 2-by-4 boards until it indicates that it is level. Now, place the attached boards on the ground (precisely where the pool will be installed) and put a level on them.

You can always outsource this wok if it seems confusing.Ģ. How can you do this? Just start off by screwing two 2-by-4 boards together (next to each other) while ensuring that they’re 1 or 2 feet longer than the overall diameter of your swimming pool. First off, check the ground to see if It’s out of level within two inches from the shallow side to the deep side. In this post, we’re going to take you through the process of leveling your pool without digging and, of course, leave you to get to work.

HOW TO SET UP ABOVE GROUND POOL ON UNLEVEL GROUND HOW TO

With this in mind, it’s only reasonable to get an idea of how to level the ground for your pool correctly (of course, without digging). You might not know this, but an improperly installed pool can be incredibly dangerous to anyone using it (which, of course, is a sure-fire way to ruin summer fun!). In addition to being aesthetically pleasing, a well-installed pool will turn out to be safe for you and your family.

HOW TO SET UP ABOVE GROUND POOL ON UNLEVEL GROUND INSTALL

Of course, basically, every one of us knows just how important it is to install or level an above ground pool properly and also maintaining it consistently despite the cost. But hey, do you know that you can get the job done without digging? Well, yes, you can! Just think it to be a much more comfortable and cost-effective way to level your pool for the ultimate summer fun. Trying to figure out how to level the ground for your swimming pool this summer? Yes, we know just how much work you have to put in to pull this off ( excavating, digging, and whatnot).

How to set up above ground pool on unlevel ground